A home for the things I think are worthy of sharing. Will largely be photography based.

Posts tagged “skyport

Mixing Nikon CLS + traditional radio trigger

Requirement/issue

At a recent event I tried to use an on-camera speedlight (SB-800) as a master  and a off-camera speedlight (again SB-800) in a CLS  setup where I would hopefully use the off-camera flash as a silhouette light.

(CLS = Nikon Creative Lighting System – where you can remotely fire flash using TTL – either with the on-bard flash (on some cameras) or another speedlight set to master. As well as using TTL you can also add compensation values to each group of remotes from the master.)

Although I’d tested them before getting into position (so channels and groups were fine) – the remote flash just didn’t fire. It was relatively in line of sight so that shouldn’t have been the issue, however with the speedlight facing forward the detector would be at the side of the speedlight and it was behind a shoot-through umbrella. I now think that possibly the combination of these meant that the signal from the master speedlight wasn’t getting through to the remote. It was also in a party environment so there were other lights which may have caused issues.

Turning the shoot-through umbrella to a bounce one may have worked (it’s a convertible umbrella), but there wouldn’t have been time for that.
Taking the umbrella off may have also helped, I should have tried this but alas didn’t.

 

In the past I’ve used a remote flash like this but using a radio trigger rather than Nikon CLS system.
I didn’t go for this setup on this occasion as I needed a on-camera speedlight as it was too dark without it.
So alas I made do without the remote speedlight.

 

After the event I investigated the option of using an on-camera speedlight but also a radio-triggered remote and my results are below.

 

Only one Hotshoe

The initial issue is that cameras only have one hotshoe. The on-camera Speedlight obviously needs to go in this. However most radio-triggers are also designed to go in this. They both can’t.

 

Other connectors

Thankfully there are a set of other connectors available.

PC socket: The PC socket is the standard/traditional method of firing flash via a cable.

My D800 has one:

D800 PCSync

And so does my SB-800’s:

SB800 PC Sync

 

Usually you’d use the PC sync on the speedlight to fire the speedlight itself i.e. incoming signal. However it appears that this socket is by-directional.

 

Sync Connector: It transpires that in addition to having the Skyport trigger via the hot-shoe there is also an additional SYNC connector:

SkyportTransmitter

 

Cable

The Sync connector on the Speedlight is smaller than the usual jack – it’s a 2.5mm jack socket rather than 3.5.

So the cable needs to be a 2.5mm jack to PC sync connector.

Thankfully one of these is supplied with skyport transmitters. I hadn’t taken it out of the wrapper let alone out of the box so I wasn’t really aware of it until investigating this issue.

31RuLRcitwL._SY300_

 

Connection + Test

I wasn’t sure if it would work correctly and wasn’t sure which PC sync to use – the camera or the speedlight. My thoughts were that if the on-camera speedlight was in TTL that there may be a flash sync speed issue, particularly with the TTL pre-flashes. So I tried both.

Standard settings – both worked.

Pushing shutter speed up to 1/250th – both worked!
(My skyport are the “SPEED” variety so are faster than the older non-speed variety)

 

To reiterate, the setup is:

Remote Speedlight: Set to manual power, skyport receiver plugged in to the PC sync port.

On-camera Speedlight: Set to TTL, mounted on camera hotshoe.

Skyport Trigger: Connected by above cable, to PC sync port of either camera or on-camera speedlight.

 

So in future I may try this in such scenarios. It’s handy to know that it’s possible to mix TTL/CLS and manual radio triggering.
Worth noting of course – since operated by a standard “GO” signal radio trigger- you can’t control the power from the camera. Pocket wizard have made TTL capable radio triggers (FlexTT5/MiniTT1 for firing and AC3 controller for varying power) but they’re considerably more expensive that simpler radio triggers that just send a “go” command.

 

Mounting Trigger

Found an additional issue worth noting:

Not wanting the skyport trigger dangling by a cable which can come out I considered mounting the trigger to the speedlight via something like velcro or elastic. In testing this I found that if you place the trigger flat against the speedlight – trigger: the flat side with buttons, speedlight: on top of the flash head – that the signal would not get to the receiver. I imagine this is due to interference from the pulse of the speedlight firing. Instead I think I’ll attach the trigger to the side of the speedlight with elastic.


Skyport Receiver Battery

Skyport Receiver Battery note

Not a very exciting blog post – but hopefully one that may help others.

I have a set of Elinchrom Skyport Speed radio triggers – one transmitter and two receivers. Recently one of the receivers stopped working. The transmitter has a replaceable battery but the receivers have an internal rechargeable battery which you charge by plugging in an AC adapter. The malfunctioning receiver wouldn’t turn on. When plugged in to AC power the LED would glow as it should when charging BUT a lot dimmer than the working receiver. I tried to charge it well over 3hrs as described in instructions – but then after disconnecting the power it wouldn’t work. Wouldn’t even turn on properly when the AC was plugged in as I’ve read it should.

I bought the set January 2011 so over a year ago and couldn’t find a reference to warranty period online so was worried that it would be out of warranty. However after mentioning the dilemma on Facebook, friends mentioned that under EU law electronics should have a warranty of two years. And sure enough – after contacting the retailer (Photomart) they said I could get it repaired under warranty – joy! After sending it to Photomart they sent it to The Flash Centre – the Uk distributor and service centre for Elinchrom who repaired it and sent it back.

On it’s return there was a note (below) stating that the battery had discharged so significantly that it couldn’t regain power – interesting. The note was A5 and seemed pre-prepared as if this isn’t an un-common issue- and so I thought it worth blogging so others with a similar issue and googling the issue know what to do. It may be worth charging your receivers from time to time in the hope of preventing this also – or if you commonly only use one – to swap them.

Skyport Receiver Battery note

Transcript:

The Skyport Universal Speed Receiver internal battery has been reformed due to a deep state of discharge.

The most likely cause is that the skyport has been stored away for a period of time in a discharged state.

Therefore we recommend that you recharge the skyport after each use to avoid similar occurring in the future.

The Li-ion battery charges in approx. 3hrs

Auto-Standby function after 4 hours.

Internal rechargeable battery lasts up to 30 hrs.